Untuk mendapatkan informasi lebih lengkap tentang:

Shimpo Tachometer Panel DT-501XA Series

Segera Hubungi Kami :

(62) 778 408 6403

sales@lfc.co.id

SPESIFIKASI Shimpo Tachometer Panel DT-501XA Series

Other selectable models by Shimpo Ordering Guide:

 
Shimpo DT-5TXR Panel Meter with Output Module Capability, Selectable inputs, 100-240 VAC Power
 Shimpo DT-5TXR-DC Panel Meter with Output Module Capability, Selectable inputs, 9-35 VDC Power
Shimpo DOP-BCDR BCD output module, 36 Pin Connection
Shimpo DOP-CPTR Relay output module, terminal block connection
Shimpo DOP-FVCR Analog output module (4-20mA & 0-1, 0-10, 1-5 VDC), 36-pin connection
Shimpo DOP-FVTR Analog output module (4-20mA & 0-1, 0-10, 1-5 VDC), terminal block connection
Shimpo DOP-RMTR Ratio input module, terminal block connection
Shimpo DOP-TRTR NPN open collector output module, terminal block connection

Note:

For Factory Assembled Panel Meter with Output Modules, Add Module to end of DT-5TXR Part and remove DOP. For two modules, only 1 36-Pin Module and 1 Terminal Block connection module can combine. Example: DT-5TXR-CPTR-FVC Panel Meter, 100-240VAC Power with Relay Output Terminal Module & 36-Pin Analog Output Module

 

 Shimpo Panel Meter DT-5TXR Accesories Ordering Guide:

 
Proximity Sensors BI2-S12 NPN (NO) sinking output 1.5 kHz frequency, LED indication, 6.5′ (2 m) cable, 0.08″ (2 mm) sensing distance, NEMA 6 (IP67) rating
DJ2-G NAMUR output, 3 kHz frequency, zero-sensing capability, 6.5′ (2 m) cable, 0.08″ (2mm) sensing distance, NEMA 6 (IP67) rating
MCS-3109 NPN (NO,NC) output, 300 Hz frequency, 0.32″ (8 mm) sensing distance, 6.5′ (2 m) cable, NEMA 6 (IP67) rating, for use in high vibration areas
SE-G Square wave output, 8 kHz frequency, LED indication, 18″ (0.46 m) cable, 0.04″ (1 mm) sensing distance
Retro-Reflective Photo Sensors MCS-625 Photo sensor with NPN sinking output, 250 Hz activating frequency, 10′ (3 m) cable 1″ to 3′ (25 to 914 mm) operating range
MCS-655 Photo sensor with NPN sinking output, 333 Hz activating frequency, LED status, 10′ (3 m) cable, NEMA 4 (IP65), 1″ to 3′ (25 to 914 mm) operating range for light or dark activation.
LS-S50MLR Laser sensor with NPN/PNP (NO,NC) outputs, 1.5 kHz frequency, LED indication, 6′ (1.8 m) with quick disconnect connection, NEMA 6 (IP67) rating
Rotary Pulse Generators RE1B-60F Rotary encoder in ABS housing with 60 ppr digital output, maximum speed 5000 rpm, 1.7 ft (0.5 m) cable
RE1B-600F Rotary encoder in ABS housing with 600 ppr digital output, maximum speed 5000 rpm, 1.7 ft (0.5 m) cable
RE1B-1000F Rotary encoder in ABS housing with 1000 ppr digital output, maximum speed 5000 rpm, 1.7 ft (0.5 m) cable
RE2B-30F Quadrature rotary encoder in ABS housing with Dual (90° out of phase) 30 ppr digital output, maximum speed: 5000 rpm, 1.7 ft (0.5 m) cable
RE2B-600F Quadrature rotary encoder in ABS housing with Dual (90° out of phase) 600 ppr digital output, maximum speed: 5000 rpm, 1.7 ft (0.5 m) cable
FPM-RE1B 12″ circumference wheel for use with RE1B and RE2B pulse generators
Magentic Pick-up Sensors MP-10 Sine wave output from change in magnetic to non-magnetic, change in voltage proportional to magnetic flux intensity over time, range of 0.01″ (0.25 mm) typical clearance, 10′ (3 m) cable
3030AN Sine wave output from change in magnetic to non-magnetic, change in voltage proportional to magnetic flux intensity over time, range of 0.01″ (0.25 mm) typical clearance, Amphenol connector
CABLE-3030 Optional cable for 3030AN
3070-XP12010 Sine wave output from change in magnetic to non-magnetic, change in voltage proportional to magnetic flux intensity over time, range of 0.01″ (0.25 mm) typical clearance, 10′ (3 m) cable Stainless steel housing, explosion-proof ATEX approved: II 2 GEExm II T3
Slot Type Sensor CM-SR21 For less dense materials that allows beam to penetrate through, NPN or PNP output with a 0.08″ (2 mm) gap range, NEMA 4x (IP65) housing.
CBL-75ANL Optional cable for CM-SR21 16.4′ (5 m)

 

Dapatkan Penawaran Harga

Silahkan isi formulir di bawah ini untuk mendapatkan penawaran harga terbaik dari tim kami,

Shimpo Tachometer Panel DT-501XA is a versatile indicator unit for rotational speed, transit time, duration and flow quantity of monitoring modules on any industrial floor. When connecting the Shimpo Tachometer Panel DT-501XA with a compatible in-line sensor, you can have a selectable inputs within largest digit size (22 mm high) and the smallest unit depth (92 mm) in the industry.

The application of Shimpo Tachometer Panel DT-501XA with any variety of compatible sensor inputs, allows for timing of machining operation, rate of change monitoring such as on a conveyor, elapsed time of oven curing, chemical coating and timing of PCB, improvised automation cannery-bottling line and many more. Thanks to its scalable programming, now you can have the flexibility to set up and monitor virtually any process within an affordable budget.

Shimpo Panel Meter DT-5TXR Features:

">